Driver sd needs updating please use bustype methods gentoo typedating com
Altough it was 32bit, but still, I find this quite odd.Now if this really is an error, not just buggy software, is there a way to ignore the error - I mean it boots up eventually anyway, just takes a hell of a lot of time.I don't have a RAID I think, it's marked as IDE in my bios, but I do seem to be using the jmicron technology.I haven't selected anything while doing the installation, and I'm not sure if I should have?done ACPI: Core revision 20070126 ACPI: Looking for DSDT in initramfs... SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine..
At least, I think it isn't since Mandriva booted just fine, and I don't think it's using a different kernel or some such, is it?
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 *9 10 11 14 15) ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay pnp: Pn P ACPI init ACPI: bus type pnp registered pnp: Pn P ACPI: found 16 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq".
ACPI: RSDP 000F9210, 0014 (r0 Intel R) ACPI: RSDT 7FEE3040, 003C (r1 Intel R AWRDACPI 42302E31 AWRD 0) ACPI: FACP 7FEE30C0, 0074 (r1 Intel R AWRDACPI 42302E31 AWRD 0) ACPI: DSDT 7FEE3180, 4BB6 (r1 INTELR AWRDACPI 1000 MSFT 100000E) ACPI: FACS 7FEE0000, 0040 ACPI: HPET 7FEE7E80, 0038 (r1 Intel R AWRDACPI 42302E31 AWRD 98) ACPI: MCFG 7FEE7F00, 003C (r1 Intel R AWRDACPI 42302E31 AWRD 0) ACPI: APIC 7FEE7D80, 0084 (r1 Intel R AWRDACPI 42302E31 AWRD 0) ACPI: SSDT 7FEE7F80, 015C (r1 Pm Ref Cpu0Ist 3000 INTL 20060912) ACPI: SSDT 7FEE8410, 02F1 (r1 Pm Ref Cpu Pm 3000 INTL 20040311) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 524000) 1 entries of 256 used Zone PFN ranges: DMA 0 - 524000 On node 0 totalpages: 523903 DMA zone: 56 pages used for memmap DMA zone: 1354 pages reserved DMA zone: 2589 pages, LIFO batch:0 DMA32 zone: 7108 pages used for memmap DMA32 zone: 512796 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base) IOAPIC: apic_id 4, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. Total pages: 515385 Kernel command line: root=/dev/sda1 ro vga=791 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) hpet clockevent registered TSC calibrated against HPET time.c: Detected 2395.908 MHz processor.
Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture...
A little update in hope someone out there might help out: I've been trying out other distros, notably slackware (x86 version), knoppix (didn't get it to boot properly, only one attempt though), gentoo (didn't get it to boot the installation cd, and since i couldn't get knoppix up i gave up on it temporarily).